Discovering Essential Plumbing Skills is Essential for Installing a Bathtub
Discovering Essential Plumbing Skills is Essential for Installing a Bathtub
Blog Article
In this article below you can locate a lot of dependable expertise related to A Step-by-Step Guide to Installing a Bathtub.
Mounting a bathtub isn't precisely rocket science, however it does require strong plumbing, woodworking, as well as often, tiling skills. Replacing an old bathtub with a brand-new one is additionally a reasonably tough job. If the old tub is readily accessible, the task can move quickly; if you need to open a wall surface to eliminate the old bathtub as well as position the brand-new tub, the task is much harder. In either case, the project is within a residence handyman's abilities, although you will require an assistant to leave the old tub as well as embeded in the brand-new one. Make sure you have qualified yourself for the task as well as fit trying it. Rather than hiring a service provider to take control of a halfway-completed task, it is better to consider employing one before you start. Opportunities are you might require an expert plumber to make tube connections.
This short article will aid you mount a brand-new tub in your restroom if you have currently gotten a new bathtub as well as don't require to alter the arrangement of your previous water pipelines.
Your tools and also material list must comprise the following:
Getting ready for the Installation
First of all, the supporting framework supplied with the bath must be fitted (if called for) according to the supplier's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to make sure that if the tap includes a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets system to prevent stress on the tub.
Fit the flexible tap ports to the bottom of the two faucets making use of 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. See to it you make use of all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bath should now prepare to be suited its final placement.
Removing Old Taps
If you need to change old faucets with new ones as a part of your setup, after that the first thing you must do is disconnect the water system. After doing so, switch on the faucets to drain any water remaining in the system. The process of getting rid of the existing faucets can be quite troublesome because of the restricted access that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the taps. Have a cloth all set for the remaining water that will certainly come from the pipelines. Once the supply pipelines have been gotten rid of, use the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming throughout this process. When the faucets have actually been removed, the holes in the bath/basin will have to be cleansed of any type of old securing compound.
Prior to carrying on to fit the brand-new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Setting up the Tub
Using the two wood boards under its feet, position the tub in the required position. The wood boards are helpful in equally spreading the weight of the bathtub over the location of the boards rather than concentrating all the weight onto 4 small points.
The following goal is to ensure that the bath tub is leveled all round. This can be accomplished by checking the level and adjusting the feet on the bath tub till the spirit level checks out level.
To install faucets, fit the bottom of the furthest adaptable faucet port to the proper supply pipe by making a compression join; then do the very same for the various other tap.
Activate the water system as well as inspect all joints and brand-new pipework for leakages and tighten them if required. Fill up the bathtub and additionally inspect the overflow electrical outlet as well as the normal electrical outlet for leakages.
Ultimately, repair the bathroom paneling as described in the producer's instruction manual. Tiling and also sealing around the bath tub should wait till the tub has been made use of at least once as this will resolve it right into its last placement.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic connector to stop damage to the string. One end of the port fits on the plastic tail of the tap and also the various other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly call for decreasing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, place the faucet in the installing opening in the bath/basin making certain that the washing machines are in place in between the tap and the sink. Protect the faucet in place with the producer offered backnut. As soon as the tap is firmly in position, the supply pipes can be connected to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with regular faucet adapters. The previous kind needs to be attached to the faucet finishes initially, tightening only by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the area where the bath fulfills the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can move enough to fracture an inflexible seal, triggering the water to pass through the wall surface between the bath and the tiling, resulting in problems with dampness and feasible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your components as well as fittings. They are marketed in tubes and cartridges, as well as are capable of sealing gaps up to a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to constantly load the bath tub with water prior to securing, to allow for the movement experienced when the bathtub is in use. The sealer can split relatively early if you do not take into consideration this movement before sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally easily readily available on the marketplace. It is suggested to fit the tiles making use of water-resistant or water-proof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a serious reader on Installing A Bathtub, I think sharing that portion was a good thing. You should set aside a second to promote this blog entry if you enjoyed reading it. Thank-you for taking the time to read it.
Need urgent plumbing repairs? Call. Report this page